![]() ![]() For instance, although a 40cm square seems like a large work surface to laser engrave on, it's restricted to that only. There are compromises to making multifunction hardware, and an overhead when switching tools and having to re-run calibration steps. The biggest consideration then is whether you need all of those functions. It’s all straightforward to set up, and unlike other tools there’s no calibration just plug it in.īefore starting yout project, you need to manually move the CNC head to the work origin zero point (just above your material, as measured using a thin sheet of paper or the 3D printing calibration card supplied). Once you’ve fitted the CNC tool head, you’ll need to use a couple of spanners to attach the desired bit securely. The CNC head is supplied with three drill bits: a thick one for general-purpose woodworking, a thinner one for plastic, and a chiseled one for detail work. However, it's $25 to replace, so it's not a huge expense if you do entirely mess it up. The wooden plate is a consumable because you might sometimes cut through the workpiece and into it, though you can mitigate this with another piece of scrap wood underneath as long as you're careful. While the bulk of it came away easily, removing it from the base around the studs was a nightmare.Īgain, switching to the CNC tool is very simple you swap over the build tray to the wooden one with a series of bolt holes to attach clamps to, and slot in the tool head. My first print was a LEGO-compatible Christmas ornament, using the breakaway filament for support. Of course, the enclosure is a great help there, in that it completely prevents draughts from spoiling the temperatures. ![]() Leveling is superb, and I had gorgeous first layers with no warping. The PEI-coated glass bed is going to give the best results and is easiest to work with. The most important thing for any 3D print is the first layer and adhesion, and my results on this front were incredible. Once integrated with the native Luban software, you'll be able to print over Wi-Fi. When I began reviewing the Artisan, the 3D printing features were not yet supported by the official Luban software, so I used their provided Cura profile instead. For small objects, you only need the middle heated, so that saves on the power bill. One small feature I appreciated was the option not to heat the entire print bed. Each is fed by a Bowden tube, which leads through the case to the filament holders on the outside. With two entirely separate extruders, the Artisan eliminates that problem and makes dual-color printing effortless. In the past, I've had no end of issues with dual-color printers which used two feeds to the same hot-end, with frequent jams and complicated procedures to changeover filaments. Swapping the tool head and build plate is effortless thanks to a single clamp system, and the only quirk to remember is that the build plate for 3D printing needs to plugged in. ![]() The supplied 3D print plate is double-sided, with one entirely glass for a very smooth surface, and the other a textured PEI surface. It also auto-detects the hot-end type allowing for quick changeovers and easy repairs, and while there are no alternatives at the moment, it's likely that larger extruders will be available in the future. It's a dual-extrusion printer with two independently heated print heads, and it can print up to 300C, so there's no material it won't be able to handle. The 3D printing aspect of the Snapmaker Artisan is likely the most familiar, and the primary reason you're buying this. It may be space-saving compared to three separate industrial-sized machines, but it is not, by any definition, compact or desktop-sized. The biggest takeaway from the Snapmaker Artisan design that I'd like to convey is that you will need a lot of space, not only for the enclosure, and the control system attached to the side of it, but also the box of different build plates, tool heads, and the toolbox. It's very explicit with instructions because it can be-it has such a large screen area to tell you what to do that you can't get confused at any step. It features a full metal enclosure and 7-inch color touchscreen, USB ports on the side and back, Wi-Fi connectivity, and is the most easy-to-use control system I've come across yet. ![]() Now, this is far more advanced than your average 3D printer control module. The Artisan also has a large control system attached to it (19 x 19 x 30cm, or 7.5 x 7.5 x 11.8 inches), with around ten cable bundles that go back to the machine, controlling each axis, the tool head, heated bed, extractor fan, and lighting, etc. But it's not just the enclosure you'll need to accommodate. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |